Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| support:fx3_bricked [2020/04/16 23:18] – Richard Neumann | support:fx3_bricked [2022/04/04 23:32] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | **LED Color Codes**\\ | + | ====== |
| - | *WHITE | + | |
| - | *BLUE – bootloader mode FX3 failed to initiate but is programmable via USB\\ | + | * WHITE ⇒ GREEN: normal |
| - | *Faint or pulsing RED – low power use AUX power supply\\ | + | * BLUE: bootloader mode (FX3 failed to initiate but is programmable via USB) |
| - | *RED – FX3 failed to initiate\\ | + | * Faint or pulsing RED: low power - use AUX power supply |
| + | * RED: FX3 failed to initiate | ||
| + | |||
| + | ===== Note: When programming the FX3 ===== | ||
| - | **Note: | ||
| AUX power should be removed | AUX power should be removed | ||
| SFP module should be removed | SFP module should be removed | ||
| The goal is to get the FX3 into Bootloader Device mode | The goal is to get the FX3 into Bootloader Device mode | ||
| - | **First Method**\\ | + | ====== |
| - | 1. Close SCC Power off camera (unplug USB)\\ | + | |
| - | 2. Make sure no SFP modules are attached\\ | + | |
| - | 3. Plug in USB\\ | + | |
| - | 4. Relaunch SCC\\ | + | |
| - | 5. Using SCC Upgrade the FX3\\ | + | |
| - | 6. IF THIS FAILS\\ | + | |
| - | **Second Method**\\ | + | - Close SCC |
| - | 7. Power Camera | + | |
| - | 8. If LED is Blue camera has reset to bootloader device\\ | + | - Make sure no SFP modules are attached |
| - | 9. Goto step **3**\\ | + | - Plug in USB |
| - | 10. IF THIS FAILS\\ | + | - Relaunch SCC |
| + | - Using SCC Upgrade the FX3 | ||
| + | | ||
| - | **Third | + | ====== Second |
| - | 11. Download Cypress USB Control center from [[support: | + | - Power Camera off for 10 minutes (same as first method with 10 minute reset) |
| - | 12. Download FX3 img file from [[support: | + | - If LED is Blue camera has reset to bootloader device |
| - | 13. Plug in USB cable\\ | + | - Goto **Third Method** |
| - | 14. Launch Cypress USB Control Center | + | - IF THIS FAILS |
| - | 15. If you see **SUB2r USB3.0 HD Camera** in the left panel\\ | + | |
| - | 16. USE SCC to update the FX3 or got to Alternative step 25\\ | + | |
| - | 17. If you see **Cypress FX3 USB BootLoader Device** Choose this\\ | + | |
| - | 18. Choose **Program**\\ | + | |
| - | 19. Choose **FX3**\\ | + | |
| - | 20. Choose **SPI Flash**\\ | + | |
| - | 21. From a drop down menu select the file location you saved the FX3 img file to and **OPEN** **SUB2r_FX3_1_1_4_5_## | + | |
| - | 22. | + | |
| - | 23. | + | |
| - | 24. | + | |
| + | ====== Third Method ====== | ||
| + | - Download Cypress USB Control center from [[http:// | ||
| + | - Download FX3 img file from [[http:// | ||
| + | - Plug in USB cable | ||
| + | - Launch Cypress USB Control Center - CCC | ||
| + | - If you see **SUB2r USB3.0 HD Camera** in the left panel | ||
| + | - USE SCC to update the FX3 or go to Alternative step 1 | ||
| + | - If you see **Cypress FX3 USB Bootloader Device** Choose this | ||
| + | - Choose **Program** | ||
| + | - Choose **FX3** | ||
| + | - Choose **SPI Flash** | ||
| + | - From the drop down menu select the file location you saved the FX3 img file to and **OPEN** **SUB2r_FX3_1_1_# | ||
| + | - Bottom left hand side message should read Programming of SPI FLASH in Progress... | ||
| + | - Bottom left hand side message should read Programming of SPI FLASH Succeeded | ||
| + | - Camera is now reprogrammed and functional | ||
| + | - | ||
| - | **Alternative if CCC sees device as SUB USB3.0 HD Camera**\\ | + | ====== |
| - | 25. From SCC select **Expert** Tab\\ | + | |
| - | 26. | + | |
| - | 27. | + | |
| - | 28. | + | |
| - | 29. | + | |
| - | 27. | + | |
| - | 28. | + | |
| - | 29. | + | |