Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
support:fx3_bricked [2020/04/16 22:47] – Richard Neumann | support:fx3_bricked [2022/04/04 23:32] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | **LED Color Codes**\\ | + | ====== |
- | *WHITE | + | |
- | *BLUE – bootloader mode FX3 failed to initiate but is programmable via USB\\ | + | * WHITE ⇒ GREEN: normal |
- | *Faint or pulsing RED – low power use AUX power supply\\ | + | * BLUE: bootloader mode (FX3 failed to initiate but is programmable via USB) |
- | *RED – FX3 failed to initiate\\ | + | * Faint or pulsing RED: low power - use AUX power supply |
+ | * RED: FX3 failed to initiate | ||
+ | |||
+ | ===== Note: When programming the FX3 ===== | ||
- | **Note: | ||
AUX power should be removed | AUX power should be removed | ||
SFP module should be removed | SFP module should be removed | ||
+ | The goal is to get the FX3 into Bootloader Device mode | ||
+ | |||
+ | ====== First Method ====== | ||
+ | |||
+ | - Close SCC | ||
+ | - Power off camera (unplug USB) | ||
+ | - Make sure no SFP modules are attached | ||
+ | - Plug in USB | ||
+ | - Relaunch SCC | ||
+ | - Using SCC Upgrade the FX3 | ||
+ | - IF THIS FAILS | ||
- | **First | + | ====== Second |
- | 1. Power cycle camera.\\ | + | |
- | 2. Make sure no SFP modules are attached\\ | + | - If LED is Blue camera |
- | 3. Close SCC\\ | + | |
- | 4. Relaunch SCC\\ | + | |
- | 5. Using SCC Upgrade the FX3\\ | + | |
- | 6. | + | |
- | **Second | + | ====== Third Method |
- | 7. Power Camera off for 10 minutes\\ | + | - Download Cypress USB Control center from [[http:// |
- | 8. If LED is Blue camera | + | - Download FX3 img file from [[http:// |
- | 9. | + | - Plug in USB cable |
- | 10. IF THIS FAILS\\ | + | - Launch Cypress USB Control Center - CCC |
+ | - If you see **SUB2r USB3.0 HD Camera** in the left panel | ||
+ | - USE SCC to update the FX3 or go to Alternative step 1 | ||
+ | - If you see **Cypress FX3 USB Bootloader Device** Choose this | ||
+ | - Choose **Program** | ||
+ | - Choose **FX3** | ||
+ | - Choose **SPI Flash** | ||
+ | - From the drop down menu select the file location you saved the FX3 img file to and **OPEN** **SUB2r_FX3_1_1_# | ||
+ | - Bottom left hand side message should read Programming of SPI FLASH in Progress... | ||
+ | - Bottom left hand side message should read Programming of SPI FLASH Succeeded | ||
+ | - Camera is now reprogrammed and functional | ||
+ | - | ||
- | **Third Method\\** | + | ====== Alternative if CCC sees device as SUB USB3.0 HD Camera |
- | 11. Download Cypress USB Control center from [[support: | + | - From SCC select |
- | 12. Download FX3 img file from [[support: | + | - From the drop down select |
- | 13. Plug in USB cable\\ | + | - First drop down menu will indicate Check if BL is Running - select drop down |
- | 14. Launch Cypress USB Control Center - CCC\\ | + | - Chose **Bootloarder mode** |
- | 15. If you see SUB2r USB3.0 HD Camera | + | |
- | 16. | + | |
- | 17. If you see **Cypress FX3 USB BootLoader Device** Choose this\\ | + | - Camera should now appear in CCC as a **Cypress |
- | 13. Choose | + | - Go to Step 6 of Third Method |
- | 14. Choose | + | |
- | 15. Choose | + | |
- | 16. From | + | |
- | 17. *OR expert mode FPGA menu 2 Bootloader mode\\ | + | |