Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
support:fx3_bricked [2020/04/16 22:22] – Richard Neumann | support:fx3_bricked [2022/04/04 23:32] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | 1. LED Color codes\\ | + | ====== |
- | a. WHITE to GREEN normal\\ | + | |
- | b. BLUE – bootloader mode FX3 failed to initiate but is programmable via USB\\ | + | * WHITE ⇒ GREEN: normal |
- | c. Faint or pulsing RED – low power use AUX power supply\\ | + | |
- | d. RED – FX3 failed to initiate\\ | + | |
- | 2. Power cycle camera. Make sure no SFP modules attached. | + | |
- | 3. Leave camera powered | + | |
- | 4. USB on if blue LED = bootloader\\ | + | ===== Note: When programming the FX3 ===== |
- | 5. Using SCC reprogram FX3\\ | + | |
- | 6. Download Cypress USB Control center from wiki.sub2r\\ | + | AUX power should be removed |
- | 7. Wiki.sub2r FX3 upgrade gone wild\\ | + | SFP module should be removed |
- | 8. Plug in USB cable\\ | + | The goal is to get the FX3 into Bootloader Device mode |
- | 9. Launch Cypress USB Control Center - CCC\\ | + | |
- | 10. If you should | + | ====== First Method ====== |
- | 11. USE SCC to update the FX3*\\ | + | |
- | 12. Cypress FX3 USB BootLoader | + | - Close SCC |
- | 13. Choose Program\\ | + | - Power off camera |
- | 14. Choose FX3\\ | + | - Make sure no SFP modules |
- | 15. Choose SPI Flash\\ | + | - Plug in USB |
- | 16. From a drop down menu select | + | - Relaunch SCC |
- | 17. *OR expert mode FPGA menu 2 Bootloader | + | - Using SCC Upgrade |
+ | - IF THIS FAILS | ||
+ | |||
+ | ====== Second Method ====== | ||
+ | - Power Camera | ||
+ | - If LED is Blue camera has reset to bootloader | ||
+ | - Goto **Third Method** | ||
+ | - IF THIS FAILS | ||
+ | |||
+ | ====== Third Method ====== | ||
+ | - Download Cypress USB Control center from [[http:// | ||
+ | - Download FX3 img file from [[http:// | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | - If you see **Cypress FX3 USB Bootloader | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | - Bottom left hand side message should read Programming of SPI FLASH in Progress... | ||
+ | - Bottom left hand side message should read Programming of SPI FLASH Succeeded | ||
+ | - Camera is now reprogrammed and functional | ||
+ | - | ||
+ | |||
+ | ====== Alternative if CCC sees device as SUB USB3.0 HD Camera ====== | ||
+ | - From SCC select **Expert** Tab | ||
+ | - From the drop down select **FPGA Console...** | ||
+ | - First drop down menu will indicate Check if BL is Running - select drop down | ||
+ | - Chose **Bootloarder | ||
+ | - **RUN** | ||
+ | - **OK** | ||
+ | - Camera should now appear in CCC as a **Cypress FX3 Bootloader Device** | ||
+ | - Go to Step 6 of Third Method | ||