Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| support:fx3_bricked [2020/04/16 22:57] – Richard Neumann | support:fx3_bricked [2022/04/04 23:32] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | **LED Color Codes**\\ | + | ====== |
| - | *WHITE | + | |
| - | *BLUE – bootloader mode FX3 failed to initiate but is programmable via USB\\ | + | * WHITE ⇒ GREEN: normal |
| - | *Faint or pulsing RED – low power use AUX power supply\\ | + | * BLUE: bootloader mode (FX3 failed to initiate but is programmable via USB) |
| - | *RED – FX3 failed to initiate\\ | + | * Faint or pulsing RED: low power - use AUX power supply |
| + | * RED: FX3 failed to initiate | ||
| + | |||
| + | ===== Note: When programming the FX3 ===== | ||
| - | **Note: | ||
| AUX power should be removed | AUX power should be removed | ||
| SFP module should be removed | SFP module should be removed | ||
| + | The goal is to get the FX3 into Bootloader Device mode | ||
| + | |||
| + | ====== First Method ====== | ||
| + | |||
| + | - Close SCC | ||
| + | - Power off camera (unplug USB) | ||
| + | - Make sure no SFP modules are attached | ||
| + | - Plug in USB | ||
| + | - Relaunch SCC | ||
| + | - Using SCC Upgrade the FX3 | ||
| + | - IF THIS FAILS | ||
| - | **First | + | ====== Second |
| - | 1. Power cycle camera.\\ | + | |
| - | 2. Make sure no SFP modules are attached\\ | + | - If LED is Blue camera |
| - | 3. Close SCC\\ | + | |
| - | 4. Relaunch SCC\\ | + | |
| - | 5. Using SCC Upgrade the FX3\\ | + | |
| - | 6. | + | |
| - | **Second | + | ====== Third Method |
| - | 7. Power Camera off for 10 minutes\\ | + | - Download Cypress USB Control center from [[http:// |
| - | 8. If LED is Blue camera | + | - Download FX3 img file from [[http:// |
| - | 9. | + | - Plug in USB cable |
| - | 10. IF THIS FAILS\\ | + | - Launch Cypress USB Control Center - CCC |
| + | - If you see **SUB2r USB3.0 HD Camera** in the left panel | ||
| + | - USE SCC to update the FX3 or go to Alternative step 1 | ||
| + | - If you see **Cypress FX3 USB Bootloader Device** Choose this | ||
| + | - Choose **Program** | ||
| + | - Choose **FX3** | ||
| + | - Choose **SPI Flash** | ||
| + | - From the drop down menu select the file location you saved the FX3 img file to and **OPEN** **SUB2r_FX3_1_1_# | ||
| + | - Bottom left hand side message should read Programming of SPI FLASH in Progress... | ||
| + | - Bottom left hand side message should read Programming of SPI FLASH Succeeded | ||
| + | - Camera is now reprogrammed and functional | ||
| + | - | ||
| - | **Third Method\\** | + | ====== Alternative if CCC sees device as SUB USB3.0 HD Camera |
| - | 11. Download Cypress USB Control center from [[support: | + | - From SCC select |
| - | 12. Download FX3 img file from [[support: | + | - From the drop down select |
| - | 13. Plug in USB cable\\ | + | - First drop down menu will indicate Check if BL is Running - select drop down |
| - | 14. Launch Cypress USB Control Center - CCC\\ | + | - Chose **Bootloarder mode** |
| - | 15. If you see **SUB2r | + | |
| - | 16. USE SCC to update | + | |
| - | 17. If you see **Cypress FX3 USB BootLoader Device** Choose this\\ | + | - Camera should now appear in CCC as a **Cypress FX3 Bootloader Device** |
| - | 18. Choose | + | - Go to Step 6 of Third Method |
| - | 19. Choose | + | |
| - | 20. Choose | + | |
| - | 21. From | + | |
| - | **Alternative if CCC sees device as SUB USB3.0 HD Camera**\\ | ||
| - | 22. From SCC select **Expert** Tabe\\ | ||
| - | 23. From the drop down select **FPGA Console...**\\ | ||
| - | 24. First drop down menu will indicate Check if BL is Running - select drop down\\ | ||
| - | 25. Chose **Bootloarder mode**\\ | ||
| - | 26. **RUN**\\ | ||
| - | 27. **OK**\\ | ||
| - | 28. Camera should now appear in CCC as a **Cypress FX3 Bootloader Device**\\ | ||
| - | 29. Go to step **17**\\ | ||
| - | ** | ||