Differences

This shows you the differences between two versions of the page.

--- support:fx3_bricked [2020/04/16 22:22] – Richard Neumann
+++ support:fx3_bricked [2022/04/04 23:32] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
-.	LED Color codes\\
+====== LED Color Codes ======
-a.	WHITE to GREEN normal\\
-b.	BLUE – bootloader mode FX3 failed to initiate but is programmable via USB\\
+    * WHITE ⇒ GREEN: normal operation
-c.	Faint or pulsing RED – low power use AUX power supply\\
+    * BLUE: bootloader mode (FX3 failed to initiate but is programmable via USB)
-d.	RED – FX3 failed to initiate\\
+    * Faint or pulsing RED: low power - use AUX power supply
-.	Power cycle camera.  Make sure no SFP modules attached.  Relaunch SCC.  Try and Upgrade.\\
+    * RED: FX3 failed to initiate
-.	Leave camera powered off for 10 minutes\\
-.	USB on if blue LED = bootloader\\
+===== Note:  When programming the FX3 =====
-.	Using SCC reprogram FX3\\
-.	Download Cypress USB Control center from wiki.sub2r\\
+       AUX power should be removed
-.	Wiki.sub2r FX3 upgrade gone wild\\
+       SFP module should be removed
-.	Plug in USB cable\\
+       The goal is to get the FX3 into Bootloader Device mode
-.	Launch Cypress USB Control Center - CCC\\
-.	If you should see SUB2r USB3.0 HD Camera in the left panel\\
+====== First Method ======
-.	USE SCC to update the FX3*\\
-.	Cypress FX3 USB BootLoader Device Choose this\\
+  - Close SCC
-.	Choose Program\\
+  - Power off camera (unplug USB)
-.	Choose FX3\\
+  - Make sure no SFP modules are attached
-.	Choose SPI Flash\\
+  - Plug in USB
-.	From a drop down menu select SUB2r_FX3_1_1_4_5_53.img\\
+  - Relaunch SCC
-.	*OR expert mode FPGA menu 2 Bootloader mode\\
+  - Using SCC Upgrade the FX3
+  - IF THIS FAILS
+====== Second Method ======
+  - Power Camera off for 10 minutes (same as first method with 10 minute reset)
+  - If LED is Blue camera has reset to bootloader device
+  - Goto **Third Method**
+  - IF THIS FAILS
+====== Third Method ======
+  - Download Cypress USB Control center from [[http://download.sub2r.com/CypressSDK1.3.4-CC.zip|Cypress's Control Center utility]]
+  - Download FX3 img file from [[http://download.sub2r.com/SUB2r_FX3_1_1_4_5_53.img|this location (FX3 build# 53 for production version of Gen 3 camera)]]
+  - Plug in USB cable
+  - Launch Cypress USB Control Center - CCC
+  - If you see **SUB2r USB3.0 HD Camera** in the left panel
+    - USE SCC to update the FX3 or go to Alternative step 1
+  - If you see **Cypress FX3 USB Bootloader Device** Choose this
+  - Choose **Program**
+  - Choose **FX3**
+  - Choose **SPI Flash**
+  - From the drop down menu select the file location you saved the FX3 img file to and **OPEN** **SUB2r_FX3_1_1_#_#_##.img**
+  - Bottom left hand side message should read Programming of SPI FLASH in Progress...
+  - Bottom left hand side message should read Programming of SPI FLASH Succeeded
+  - Camera is now reprogrammed and functional
+  -
+====== Alternative if CCC sees device as SUB USB3.0 HD Camera ======
+  - From SCC select **Expert** Tab
+  - From the drop down select **FPGA Console...**
+  - First drop down menu will indicate Check if BL is Running - select drop down
+  - Chose **Bootloarder mode**
+  - **RUN**
+  - **OK**
+  - Camera should now appear in CCC as a **Cypress FX3 Bootloader Device**
+  - Go to Step 6 of Third Method