Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| support:sub2r_cc_revision_history [2021/06/28 00:36] – [upcoming] Igor Yefmov | support:sub2r_cc_revision_history [2022/08/22 20:40] (current) – [2.6.0: 2022-08-22] Igor Yefmov | ||
|---|---|---|---|
| Line 4: | Line 4: | ||
| ===== upcoming ===== | ===== upcoming ===== | ||
| - | | + | |
| + | ===== 2.6.0: 2022-08-22 ===== | ||
| + | | ||
| + | * update to MSVC 2022 | ||
| + | * " | ||
| + | * support for Gen5 (based on Xilinx %%UltraScale%%+ and a new, much improved image sensor) | ||
| + | * includes support for dedicated SDI output and HDR mode | ||
| + | * many more '' | ||
| + | * preparing for C++20 modules support | ||
| + | * use '' | ||
| + | * SUB2r-lib | ||
| + | * up the version to '' | ||
| + | * support for sensors that are not on I²C address '' | ||
| + | * inheritance cleanup | ||
| + | * new APIs | ||
| + | * %%SysInfo%% API v.2 now reports status of peripherals - requires FX3 v60+ | ||
| + | * access arbitrary I²C-attached module on device - requires FX3 v98+ | ||
| + | * MIPI FPS - requires FPGA v76+ | ||
| + | * the connection to device is now " | ||
| + | * API duration reporting' | ||
| + | * removed an unnecessary extra layer '':: | ||
| + | * %%CyUSB%%.h no longer # | ||
| + | * support for new (and legacy) [[code: | ||
| + | * firmware update no longer overestimates the number of sectors to erase on SPI flash | ||
| + | * bugfixes | ||
| + | * ugly formatting of firmware version info | ||
| + | * non-printable characters in version check URL | ||
| + | * USB " | ||
| + | * long-standing issue of incorrectly using BULK EP4 when accessing I²C on the camera | ||
| + | * potential memory corruption in one corner case | ||
| + | * call to %%DeviceIoControl%% is using the same buffer for both IN and OUT because of a driver from Cypress, so needed a reasonable workaround (far from perfect) | ||
| + | * occasional infinite wait on exit (causing the host application to stay in memory) | ||
| + | * SCC | ||
| + | * sensor Console | ||
| + | * dialog is now resizable | ||
| + | * added register bulk compare to diff long lists of register/ | ||
| + | * "Use group write" is no longer the default behavior | ||
| + | * make %%LvL%% limits all the way to full scale of '' | ||
| + | * FPGA console | ||
| + | * now lists I²C-related APIs | ||
| + | * increased width of input boxes to accommodate 32-bit hex values | ||
| + | * under certain conditions " | ||
| + | * new I²C console (for expert users) | ||
| + | * more robust handling of being run in offline mode | ||
| + | * a new FX3 firmware can now be loaded into RAM ([Shift]-drag-n-drop of a file) | ||
| + | * support for dedicate SDI output - requires Gen5 camera | ||
| + | * bugfixes | ||
| + | * potential memory corruption in FPGA console | ||
| + | * Sensor console script now properly ignores comments (those that begin with a semicolon ";" | ||
| + | * Aria | ||
| + | * display true MIPI speed (FPS produced by sensor itself) - requires FPGA v76+ | ||
| + | * bugfixes | ||
| + | * crash on startup if sensor is inaccessible | ||
| + | * Installer | ||
| + | * removed that ancient Gen2 control center, a.k.a. "old radio" | ||
| ===== 2.5.0: 2021-06-28 ===== | ===== 2.5.0: 2021-06-28 ===== | ||